Power Distribution Box DB-9 (Blackmagic PYXIS, V-Mount) ติดตั้งเข้ากับตัวกล้องโดยตรงผ่านรูเกลียว 1/4-20 สองตัวด้านหลัง และให้การกระจายไฟอัจฉริยะพร้อมหัวต่อ D-Tap, USB-C PD 5V, ปลั๊ก Fischer 3 ขา และหัวต่อที่เข้ากันได้กับ LEMO 2 ขา สาย USB-C REMOTE แบบถอดได้ช่วยให้สามารถควบคุมเริ่ม/หยุดการบันทึกจากระยะไกลผ่านอุปกรณ์ Fischer 3 ขา
มีจำหน่ายในรุ่น 15mm LW Rod Mount แบบหมุนได้สำหรับติดตั้งในตำแหน่งที่ห่างจากกล้องมากขึ้น
สามารถสลับระหว่างแบตเตอรี่ในตัวและ DC INPUT 4 ขา XLR ได้อย่างต่อเนื่องโดยไม่สูญเสียไฟให้กล้องหรืออุปกรณ์เสริม เมื่อเชื่อมต่อทั้งสองแหล่งจ่ายไฟ DC INPUT จะมีลำดับความสำคัญสูงสุดลงมาจนถึง 12.5V ณ จุดนั้น DB-4 จะสลับไปใช้แบตเตอรี่ในตัว
การออกแบบขาตั้งช่วยให้สามารถติดตั้งแบตเตอรี่ Sony BP-U35 ในกล้องเพื่อใช้เป็นแบตสำรองฉุกเฉิน ในการเปลี่ยนแบตภายใน ให้เหวี่ยง DB-9 ขึ้นและปลดแบตเตอรี่ออก
DB-9 สามารถแยกออกจากขาตั้งกล้องได้ โดยจะเปิดเผยแคลมป์แกน 15 มม. พร้อมปลอกป้องกันแรงเสียดทานภายใน
ด้วยการออกแบบ SMART FUSE ระบบจะตรวจสอบการใช้ไฟของกล้องและจัดสรรงบประมาณไฟที่เหลือให้กับอุปกรณ์เสริม ตัวอย่างเช่น C80 ใช้ไฟประมาณ 1.8A ที่ 14V ดังนั้นเมื่อใช้แบตเตอรี่ที่รองรับ 10A กระแสที่เหลือ 8.2A จะถูกจัดสรรสำหรับใช้กับอุปกรณ์เสริม หากการกำหนดค่าอุปกรณ์เสริมเกินขีดจำกัด 8.2A ไฟจ่ายไปยังอุปกรณ์เสริมจะถูกตัดออก โดยกล้องจะยังคงได้รับไฟ ไฟ LED “SMART FUSE” จะสว่างแสดงข้อผิดพลาด และเมื่อปรับการกำหนดค่าให้ต่ำกว่า 8.2A แล้ว จึงสามารถกดปุ่ม RESET และเปิดไฟจ่ายไปยังขั้วออกอุปกรณ์เสริมใหม่ได้
ในกรณีที่เกิดการลัดวงจรสมบูรณ์ ระบบจะปิดทันทีและสามารถเปิดใหม่ได้เมื่อปัญหาการลัดวงจรได้รับการแก้ไขแล้วเท่านั้น
มีแผ่นยึด Gold Mount แบบเปลี่ยนได้โดยผู้ใช้เองด้วย
อินพุต
- BATT: แผ่นยึด V-Mount
- DC IN: 4 ขา XLR (11-17V)
เอาท์พุต
- D-Tap 2 ตัว (แรงดันแบตเตอรี่)
- 3 ขา 2 ตัว (24V ที่ 2.5A พร้อมฟังก์ชัน run/stop)
- 2 ขา 2 ตัว (แรงดันแบตเตอรี่)
- USB-C PD 1 ตัว (5V ที่ 3A พร้อมล็อคเกลียว)
มีจำหน่ายในรุ่น Gold Mount ด้วย!
น้ำหนักผลิตภัณฑ์: 13.6oz (385g)
Power Distribution Box DB-9 (Blackmagic PYXIS, V-Mount) attaches directly to the camera body using the rear two 1/4-20 threaded holes and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable REMOTE USB-C cable enables remote start/stop capability using 3pin Fischer devices.
Also available in a hinged 15mm LW Rod Mount version for attaching further away from the camera.
Hot-swap between on-board battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-4 will switch to an onboard battery.
The mount design allows a Sony BP-U35 battery to be installed in the camera to function as an emergency backup. To swap the internal battery, swing the DB-9 up and release the battery.
The DB-9 can also be separated from its camera mount, revealing a 15mm rod clamp with an internal friction sleeve.
With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the C80 uses approximately 1.8A at 14V so when using a 10A capable battery, the remaining 8.2A is allocated for accessory use. If an accessory configuration exceeds the 8.2A limit, accessory power is cut off, leaving the camera powered. The “SMART FUSE” LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 8.2A, the RESET button can be pressed, and power will be re-enabled to accessory outputs.
In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.
User changeable Gold Mount Plates are available as well.
INPUTS
BATT V-Mount plate
DC IN 4pin XLR (11-17V)
OUTPUTS
2x D-Tap (battery voltage)
2x 3pin (24V at 2.5A with run/stop)
2x 2pin (battery voltage)
1x USB-C PD (5V at 3A with thread lock)
Also available in a Gold Mount version!
Product Weight: 13.6oz (385g)